Osmo anti slip Decking Oil meets the demands of hardwood decking. Decking oil protects, maintains and beautifies the wood surface, producing a smooth slightly satin-matt finish which is extremely water resistant and dirt repellent. The microporous finishes are based on natural vegetable oils and allow the wood to breathe and help regulate the moisture content reducing swelling and shrinkage, the finish will not crack, flake, peel or blister.
430 Anti-Slip Decking Oil Clear (top coat only)
Note: Some variation may occur due to screen brightness and uploading processes. It is advisable to test colours on a small sample, as some colours may appear differently on other wood species.
- Approx. coverage : 16m²/L with one coat
- Number of coats : 2 coats
- Aplication tools : Brush
- Application temperature : +5°C to 35°C
- Approx. drying time : 8-10hrs.
- Sizes: 0.750L, 2.5L
Designed and produced to meet the individual demands of exotic wood species, especially recommended for garden furniture and wood decking.
For a clear and natural finish for decking, apply just two coats of 007 Teak Oil. The darker the colour, the higher the uv-protection is provided. Anti-Slip Decking Oil 430 Clear can only be used as a top coat over a pigmented finish, please do not use over a clear finish such as 007 Teak Oil.
We recommend a base coat with a coloured Osmo Decking Oil, such as: Osmo Bangkirai-Oil, Larch-Oil or Douglas Fir Oil or Osmo Natural Oil Woodstain.
Before applying an Osmo coloured base coat ensure the bare wood species has been properly prepared. Please refer to the coloured Osmo Decking Oil product for more guidance on wood species preparation. Osmo Anti-Slip Decking Oil 430 top coat acts as protection against weathering and extends the life of the coating.
Wood surface must be clean, dry and frost-free (moisture content max. 20%). Osmo Anti-Slip Decking Oil 430 is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use.
For renovation works, clean existing, intact Osmo Decking oils thoroughly with diluted Osmo Decking Cleaner. De-grey and clean already greyed or weathered wood at the same time with Osmo Wood Reviver Power-Gel and rinse well. Avoid using jet / power washers to clean as this can be detrimental to the existing coating and reduce coverage of an Osmo finish.
The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
METHOD OF APPLICATION
With Osmo Flat Brush, apply thinly along the wood grain and spread well. For quicker application on larger areas, we recommend our Osmo Decking Brush (150 mm) which is tailored for decking and allows you to work ergonomically. Spread well and evenly.
Allow to dry for approx. 12 hours under good ventilation.
For renovation works, one coat applied to the clean and dry surface is usually sufficient.
Osmo Anti-Slip Decking Oil 430 is clear satin and therefore it offers only limited protection against UV radiation (greying). With a combination of a coloured base coat and a top coat with Osmo Anti-Slip Decking Oil 430, your decking is fully protected. Osmo Anti-Slip Decking Oil 430 is not suitable for a single product application. Oils enhance the natural colour tone of wood (permanent wet effect).
To avoid greying and declining non-slip effect on high traffic areas, these areas should be cleaned and recoated at the right time.
If the greying process has already begun, de-grey the surface with Osmo Wood Reviver Power-Gel, rinse well then recoat.
Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered.
Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating.
Regular Cleaning: Damp cleaning with Osmo Decking Cleaner using Osmo Decking Cleaning Brush.
Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean ( for green growth) .
Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.